The System Has Encountered an Error. Please Come Back and Try Again Later.

"DiskPart has encountered an error: The parameter is incorrect" error can exist occurred when you try to format a drive using the "format fs=ntfs" command using DiskPart tool. The error is appeared later on the format procedure reaches the 100%, without an obvious reason.DiskPart is a powerful disk utility which is unremarkably used to manage disks, partitions, or volumes that cannot be managed using Windows Disk Director options. For example, if y'all accept a Hard Disk, a USB Wink Bulldoze or an SD Carte that cannot be formatted or accessed by Windows due to data corruption or other bug, you can employ the DiskPart tool to format the disk.

DiskPart tool must exist used very carefully, considering information technology can ERASE everything on the selected difficult bulldoze, so before using it make sure that you already accept a backup of your data to another storage media.

In this tutorial you 'll find detailed instructions on how to resolve the "DiskPart has encountered an mistake: The parameter is incorrect" error.

How to FIX: DiskPart has encountered an error: The parameter is wrong

Important Notes:
one. Before you continue, unplug all unneeded storage devices from your estimator (USB disks, Memory cards, etc.).
2. Advisedly select the drive (disk) that you desire to format to avoid losing your data.
3. Don't forget to launch Command Prompt with Administrative privileges, in order to run DiskPart.

– To resolve the "DiskPart has encountered an error: The parameter is incorrect" mistake afterward running the "format fs=ntfs" command in DISKPART utility, try the following steps:

Method 1.

ane. In command Prompt type: diskpart and press Enter.
2.Type the post-obit command to list all the available drives and press Enter:

• list disk

iii. Carefully locate the disk that you want to format (eastward.m. the "disk 1" in this example) and then type the following command to select the disk by using it'south number (eastward.yard. "1") and press Enter: *

• select disk 10

* Note: Where "X" is the disk number of the deejay that you lot want to format.. Change information technology co-ordinate your case (e.g. "select disk 1").

4. Then type the following control to totally erase the disk and printing Enter. *

• make clean

5. When the "Clean" is completed, type the following control to create a sectionalisation on the disk and printing Enter:

• create partitioning primary

vi. Now give the following command to select the created sectionalization and printing Enter:

• select partition 1

7. Finally format the select partition, using the following command and printing Enter:

• format fs=ntfs quick

8. Assign a drive alphabetic character (eastward.one thousand. "Z:") on the deejay/partition.

• assign letter=Z

9. Finally blazon leave and printing Enter to close DiskPart tool.

– If after following the above procedure, you still receive the "DiskPart has encountered an fault: The parameter is incorrect" error then go along to side by side method below.

Method 2.

– Run DiskPart again and supplant the clean command with clean all and instead of the format fs=ntfs quick command type format fs=ntfs (without quick).

• diskpart
• list disk
• select disk X

* Annotation: Where "X" is the disk number of the disk that you desire to format. Change information technology co-ordinate your case (eastward.g. "select disk i").

• clean all

* Notation:  The "clean all" control should have some time, so be patient.

• create partition primary
• select division one
• format fs=ntfs
• assign letter=Z
• exit

Method 3.

– Try to delete all volumes on the disk and and so specify the partition structure type (MBR or GPT) by following the process beneath:

• diskpart
• list disk
• select disk Ten

* Note: Where "X" is the disk number of the disk that you lot want to format. Change it according your instance (e.g. "select disk 1").

• detail disk

* Notation: The "detail deejay" command shows only the book(southward) of the selected disk.

• select volume X

* Note: Where "10" is the volume number that the selected disk contains. Change information technology according your example (e.chiliad. "select book 4").

• delete volume

* Note: If you found, more than one volumes on the selected disks, then "select" and "delete" all of them (one by ane).

• select disk X

* Note: Where "Ten" is the disk number of the disk that you desire to format. Modify it according your case (due east.thousand. "select deejay i").

• catechumen mbr

* Note: If you take a disk over 2TB, and then use the catechumen gpt command instead.

• clean
• create partitioning primary
• select sectionalisation 1
• format fs=ntfs quick
• assign alphabetic character=Z
• get out

Other methods to fix the "The parameter is incorrect" mistake in DISKPART.

one. If the "The parameter is incorrect" error is occurred when you try to format a USB disk, effort to format the disk past using the: HP USB Disk Storage Format Tool.
two. If the "The parameter is incorrect" fault is occurred when you try to format an SD bill of fare, then use the SD Menu Formatter tool.
3. Check the hd for problems, by using the instructions on this article: Best Difficult Drive Examination & Diagnostic Tools to Check Hard disk'south Health. If the deejay is damaged, and so replace the deejay.

That's it! Let me know if this guide has helped you by leaving your comment about your experience. Please similar and share this guide to help others.

If this article was useful for y'all, please consider supporting the states by making a donation. Even $1 can a make a huge difference for us.

solanoskiatio.blogspot.com

Source: https://www.repairwin.com/fix-diskpart-has-encountered-an-error-the-parameter-is-incorrect/

Share this post